CM Toolkit Search

Parting Shots

Eras of Innovation

As the industry heads into 2017 focused on solving workforce issues with greater manufacturing efficiency, it’s instructive to look back at the August 2006 issue of SBC Magazine, which featured an interview with Gene Woloveke, the inventive force behind the Idaco Machine & Equipment Company.

Presentation

Framing the American Dream: Wall Labor

This slide deck provides more information about the Framing the American Dream project, as well as more in-depth information about what was learned when comparing the two wall framing methods. These slides can be downloaded and customized in any way you choose.

Guidance Document

Promoting Wall Panels to Builders

If you are interested in promoting your wall panel packages to builders who prefer to stick-frame walls in the field, here are some tools you can use to begin that discussion.

Guidance Document

Promoting Wall Panels to Framers

If you are interested in promoting your wall panel packages to framers who prefer to stick-frame walls in the field, here are some tools you can use to begin that discussion.

Alternate Nailing Patterns

Question: 

Some truss lumber repair nailing patterns call for 16d common nails. Most nail guns do not support 16d nails, but have an equivalent to a 12/10d nail. Is there a substitution guide or ESR report that could help us?

Hanger Nails Above The Neutral Axis

Question: 

I recall seeing a design recommendation several years ago regarding installation of hanger nails above the neutral axis of the bottom chord of a plated girder truss. The intent was to avoid dumping large loads into the bottom chord, below the neutral axis. Can you tell me where I can find this information?

Roof Truss Nailing With Hurricane Clips

Question: 

If you use hurricane clips to secure roof trusses from uplift, are you allowed to use fewer than the typical three nails in the bearing heel of the roof truss? I am concerned because we want to do the right fastening schedule, but three nails in addition to the hurricane clip splits the wood. What is the standard recommendation?

Attachment Of Scissors Trusses

Question: 

What is the correct method of attaching scissors trusses to the top plate? I read recently in a trade magazine that this type of truss should be toe-nailed on one end and attached with slotted clips on the other end. According to the article, this is to allow for movement of the truss. We require PE stamped spec sheets from the truss manufacturer to verify trusses meet wind and snow loads. These sheets give bracing requirements but never give recommended attachment requirements.

Bracketless Connections

Question: 

Are there any trusses that are supported strictly by the wood itself without any mechanical connections such as brackets?

Blocking For Lateral Displacement And Rotation

Question: 

I am a building inspector and have some questions regarding how to apply IBC 2012 2308.8.5 (IRC 2012 R802.8) (similar IBC 2015 2308.4.6 & IRC 2015 R802.8) to trusses, especially those with high heels:

Truss Attachment Information

Question: 

Would you please inform me of the specified requirements of the size and the amount of nail attachments from the truss to the top plate?

Notched Top Chords On Gable Ends

Question: 

The industry suggests notching the gable end truss to support the overhang. Is this wise? What about a structural gable, or a gable designed with drag loads, or one with only partial bearing? How safe is it for a framer working with a truss that has the top chord cut repeatedly?

Partition Wall Attachment To Bottom Chords

Question: 

I am remodeling a 16-year-old ranch style home. The roof consists of 4/12 26 ft. span trusses, 24 in. O.C., over 2x4 stud walls. What is the recommended means of affixing the top plate of new interior partitions to provide the lateral support needed for the partition? Also, I want to hang a soffit above and overhanging the new kitchen cabinets (recessed lighting placed within). What is the recommended means of attaching the soffit to the underside of the trusses so as not to interfere with the designed movement of the trusses under the variable live load experienced (snow load)?

Jack Truss Connections To Girder

Question: 

In a hip roof application where jack trusses connect to a girder truss using pressure blocking (power blocking), what is the proper installation and the span that is acceptable before a hanger is required?

Construction Loads On Floor Truss Assemblies

Question: 

How much OSB can be stacked on a floor deck without damaging the trusses?

Bottom Chord Dead Load

Question: 

I have built a 30 ft. x 40 ft. pole barn with nine 30 ft. 2x4 7/12 pitch trusses that are 5 ft. O.C. I am planning to finish out the interior and will attach 7/16 x 4 x 8 OSB sheets to the trusses for my ceiling. Along with this, I will have to add several 2x4 nailers across the 30 ft. span between the trusses to attach the sheeting to. My question is: will these trusses have any problem supporting this ceiling? I am not planning on anything being placed in the section above the ceiling and there will be no walls or supports erected between the ceiling and the floor.

Wind Loads From Solar Panels

Question: 

I am looking for information on point loading trusses. We manufacture mounting structures for solar panels. Typically, 10 to 15 sq. ft. of solar panel is supported by one standoff. Under extreme conditions – 50 lbs. per sq. ft. of wind load - we can transfer 500 to 750 lbs. of force onto one point of one truss. Are there any standards on this issue?

Drag Loads

Question: 

Can you explain drag loads and how to calculate a drag load pertaining to roof trusses?